Viking DEV900 Uživatelský manuál stáhnout pdf

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

1. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer or your distributor.

2. Before servicing or cleaning unit, switch power off

at service panel and lock the service disconnect-

ing means to prevent power from being switched

on accidentally. When the service disconnecting

means cannot be locked, securely fasten a promi-

nent warning device, such as a tag, to the service

panel.

3. Installation work and electrical wiring must be

done by a qualified person(s) in accordance with

all applicable codes and standards, including fire-

rated construction codes and standards.

4. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of

fuel burning equipment to prevent backdrafting.

Follow the heating equipment manufacturer's

guideline and safety standards such as those

published by the National Fire Protection Associa-

tion (NFPA), and the American Society for Heat-

ing, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

WARNING

CAUTION

1. For general ventilating use only. Do not use to ex-

haust hazardous or explosive material and vapors.

2. To avoid motor bearing damage and noisy and/or

unbalanced impellers, keep drywall spray, con-

struction dust, etc. off power unit.

3. Please read specification label on product for

further information and requirements.

4. Electrical circuit, including speed control, (if used),

must be rated 6 AMPS minimum.

Blower Dimensions

28.25 x 24.75 x 7.17

PLAN THE INSTALLATION

1. Locate the ventilator so the length of the duct run

and number of elbows needed are kept to a mini-

mum.

2. Where possible, ventilator should be centered

between wall studs or roof rafters.

3. Avoid pipes, wires, or other ductwork that may be

running through the wall.

ALL INSTALLATIONS

MODEL VOLTS AMPS CFM DUCT SIZE

DEV900 120 5.7 900 10 " DIA.

SPECIFICATIONS

INSTALLER: Leave This Manual With The Homeowner

HOMEOWNER: Use And Care Information On Page 4

5. When cutting or drilling into wall, or ceiling, do not

damage electrical wiring or other hidden utilities.

6. Ducted fans must always be vented to the out-

doors.

7. To reduce risk of fire, use only metal ductwork.

8. This unit must be grounded.

READ AND SAVE THESE INSTRUCTIONS

VIKING MODEL DEV900

EXTERIOR MOUNTED VENTILATOR

FOR USE WITH VIKING VCWH, VICH, DBCV, DICV, DCWH, DCWL, DCWN,

DTWS AND DCIH RANGE HOODS. 30" TO 42" WIDE, 9" TO 18" HIGH.

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - EXTERIOR MOUNTED VENTILATOR

1WARNINGTO REDUCE THE RISK OF FIRE, ELECTRICSHOCK, OR INJURY TO PERSONS, OBSERVETHE FOLLOWING:1. Use this unit only in the manner intended by themanuf

Strany 2 - 24¾"

211" dia.hole29½"11" dia.hole1¼"dia. hole127/8"10¾"25"7¼"7¼"1¼"dia. hole91/8"91/8"Wall Stu

Strany 3 - Figure 4

31. Remove roofing nails from the upper 2/3 of theshingles around the cutout area and carefully lift theshingles to allow the back flashing sheet on t

Strany 4 - MOTOR LUBRICATION

499043050EF20222USE AND CAREDisconnect electrical power supply and lock outservice panel before cleaning or servicing this unit.CLEANINGRemove cover a

Strany 5 - VIKING MODÈLE DEV900

5AVERTISSEMENTOBSERVEZ LES DIRECTIVES CI-DESSOUS DEMANIÈRE À RÉDUIRE LES RISQUES D’INCENDIE, DECHOC ÉLECTRIQUE OU DE BLESSURESCORPORELLES.1. N’utilise

Strany 6

611" dia.hole29½"11" dia.hole1¼" dia. hole127/8"10¾"25"7¼"7¼"1¼" dia. hole91/8"91/8"Wall S

Strany 7

71. Retirez les premiers deux tiers des clous à toiture desbardeaux se trouvant autour de la zone de découpe puissoulevez délicatement les bardeaux de

Strany 8 - LUBRIFICATION DU MOTEUR

8GREENWHITEBLACKGREENWHITEBLACKBLACKWHITEGREENBLACKWHITEGREENROUGH-IN PLATE LEADROUGH-IN PLATE LEADWIRING BOXLINE IN120 VAC60 HZ10 A MAX.EXTERIORBLOWE