Viking C-1000B Specifikace Strana 5

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 8
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 4
H. Using the C-1000B on an Analog Station Port (Analog PABX/KSU Station Mode)
Note: This mode can NOT be used with W-1000, W-2000A or W-3000 doorboxes. This application is ideal for connecting the
C-1000B to an unused analog station of your phone system. See Programming section F and Operation section A.
DOOR ENTRY / CCTV VIDEO
CONTROLLER
VIKING
©
MODEL C-1000B
PWR 13.8 VAC
DOOR
STRIKE 1
DOOR
STRIKE 2
DOORBOX 2
DOORBOX
PWR OUTPUT
DOORBOX 1
123456789
10 11 12 13
14 15 16 17 18 19
EARTH
GND
PHONE LINE
INPUT
LINE OUT
TO PHONES
KEYLESS CONTACT
CLOSURE INPUT
VIKING
ELECTRONICS
HUDSON, WI 54016
EARTH
GND
C.O. LINE
INPUT
OUT TO
PHONES
KEYLESS
C.C. INPUT
DOOR
BOX 1
DOORBOX
13VAC PWR
DOOR
BOX 2
N.O. COM N.C.
DOOR STRIKE 1
SIG GND
VIDEO 1 IN
SIG GND
VIDEO 2 IN
SIG GND
VIDEO OUT
N.O. COM N.C.
DOOR STRIKE 2
TALK BATTERY
OFF ON
C
LED1
C
LED2
C
LED3
ON
1 2 3
COM N.O. N.C. - - - - AUX.
CONTACT
OUTPUT
13.8V AC
Adapter
included
120V AC
or
Standard
Analog Phone
**K-1900-5
Dialer
* K-1700-3
Phone
E-1600A
Phone
Talk Battery Switch
OFF ON
CO line or
Analog
PABX/KSU
station
E-30
Speaker Phone
Earth
Ground
(see pg 2)
E-10A or E-20B
Speaker Phones
E-10A or E-20B
Speaker Phones
5A@30V DC/
250V AC maximum
120V AC
Doorstrike/
Magnetic Lock 2
ON
1 2 3
DIP Switches
ON
OFF
Model
E-10A/E-20B
E-30
E-1600A
K-1700-3
K-1900-5
Fax #
210
212
215
157
317
Description
Handsfree Speaker Phone
Vandal Resistant Handsfree Speaker Phone
Emergency/Elevator Phone
Handsfree Speaker Phone with Keypad
Touch Tone Dialer
Need more information on the products shown to the right?
Call 715-386-4345 and enter the fax number below:
Note: The E-10A and E-20B
Speaker Phones may be used
without a dialer when installed
on a ring-down circuit.
Notes:
*1. The K-1700-3’s keypad can be used for extension dialing, etc., but
can NOT be used for keyless entry (see Installation and
Applications section D).
2. If “Switched” camera control is needed (for a switching video RF
modulator), connect the camera to “Video 2 In”, connect the RF
Modulator to “Video Out” and program the C-1000B with “ ,7 “
and “ 11 # 03”.
3. Once the “Analog PBX/KSU Station Mode” (,5) has been
programmed, you are not able to access the programming mode
of the C-1000B in the normal fashion. For details, see
Programming, Section A.
**4. The K-1900-5’s touch tone and flash restrictions must be disabled
(
,
02). See the K-1900-5 Technical Practice for complete
programming instructions, DOD# 317.
5
Important:
1. In this application, only a single door phone is used
and
,
5 must be selected when in programming.
2. Do not program the CCTV Video Control Mode (,8)
in this application (See Note 2 below). Only Auxiliary
Contact Mode (,7) can be used.
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
A. Accessing the Programming Mode
1. Accessing the Programming Mode Locally (Security Code Bypass Mode)
Follow Sections 1 or 2 to program a new C-1000B or any C-1000B that has not been previously programmed into the “Analog
PBX/KSU Station Mode” (,5). If the “Analog PBX/KSU Station Mode” has been programmed, follow Sections 3 or 4 to access pro-
gramming.
Note: If you are not sure how the C-1000B was previously programmed and have difficulty accessing the programming mode by
following Sections 1 or 2, follow Sections 3 or 4 in case the C-1000B is currently in the “Analog PBX/KSU Station Mode” (
,
5).
Step 1. Disconnect the PHONE LINE INPUT.
Step 2. Slide the TALK BATTERY switch to the ON position.
Step 3. Move DIP switch 2 from OFF to ON (see Programming section E).
Step 4. Come off-hook with a phone connected to terminals 4 & 5, LINE OUT TO PHONES.
Step 5. A double beep will indicate that you have accessed the programming mode.
Step 6. You can now Touch Tone program the features listed in section B below.
Step 7. When finished programming, hang up and move DIP switch 2 to the OFF position.
Step 8. Slide the TALK BATTERY switch back to the OFF position.
Step 9. Reconnect line to PHONE LINE INPUT.
2. Accessing the Programming Mode Remotely
Step 1. Call into the C-1000B from a Touch Tone phone.
Step 2. Answer the call using the phone (device) connected to terminals 4 & 5, LINE OUT TO PHONES.
Step 3. From either phone enter , followed by the security code (factory set to 845464, see Programming section D).
Step 4. A double beep will indicate that you have accessed the programming mode.
Step 5. You can now Touch Tone program the features listed in section B below.
Step 6. When finished, hang up both phones to exit the programming mode
Note: Programming from a cell-phone may not be suitable in areas with weak coverage.
Zobrazit stránku 4
1 2 3 4 5 6 7 8

Komentáře k této Příručce

Žádné komentáře