Viking W-3000 Specifikace stáhnout pdf (Strana 7)

Symptom 1:

The entry phone is able to call a slave apartment, but when they attempt to dial the relay command ("6" by default), the

door/gate doesn't open (the doorstrike contacts of the master C-3000 don't operate). When calling a master apartment and

dialing the relay command, the door/gate does open. Also, the doorstrike contacts of the slave C-3000 are activating when

the entry phone calls a slave apartment and the party dials the relay command (the slave C-3000's relay would not activate

in a working master/slave configuration).

Probable Cause and Solution:

Check the "multi-module interconnect" modular cord between the master and slave (or in larger "stacks", the cord between

the first slave C-3000 with the problem and the slave C-3000 ahead of it in the stack). If the cord is only a two conductor

modular cord, it must be replaced with a four conductor modular cord. If it is a four conductor modular cord, the cord has

an open in the second pair (yellow or black wires) and should be replaced (the polarity of this modular cord must be cor-

rect - see Probable Cause and Solution for symptom 2).

A. Receiving a Visitor

A visitor arrives, takes the entry phone off-hook and dials a one or two-digit code (1-96), which corresponds to an indi-

vidual tenant's apartment (see Wiring Table in Installation section D). The telephone(s) in the tenant's apartment then

begin to ring in a special "double-ring" cadence, notifying the tenant that they have a visitor at the door. The tenant may

then answer the call from any phone, and converse normally with the visitor. If the tenant's phone is already in use, the

tenant receives a "call waiting" type tone, notifying them of the visitor's call. A hookswitch flash from the tenant's phone

will put the current call on hold, and answer the visitor's call. A second hookswitch flash from the tenant's phone will

disconnect the visitor's call and return the tenant to the original call, without allowing the visitor access to the building.

Note that when either of the two entry phones are in use, the other entry phone is disabled for the duration of the call.

B. Allowing a Visitor Entry

After communicating with a visitor at the door, the tenant can allow the visitor access to the building by entering a pro-

grammable code on the tenant's touch-tone telephone. The factory default relay activation code is "6". Upon entering

this code, both parties will hear a brief buzzing tone as they are disconnected from the telephones, and the door strike

relay operates giving the visitor access to the building. If the tenant had a call in progress, the tenant will also be auto-

matically returned to the original call. If the visitor attempts to enter the relay entry code themselves, the C-3000 sys-

tem detects this and automatically disconnects both parties, without activating the doorstrike relay.

C. Keyless Entry

Each tenant can be assigned a unique four to six-digit entry code, which may be used to gain access to the building

without their key. In addition to the 96 tenant Keyless Entry codes, there is also one additional "Master" keyless entry

code. To access the Keyless Entry feature, the tenant takes an entry phone off-hook and enters "#", plus their keyless

entry code. The doorstrike relay will then operate to allow the tenant access to the building. Note that it is not a require-

ment to set or use the C-3000 keyless entry feature.

D. Changing Keyless Entry Codes or Programming Features

From the Building Manager's Phone or the “Program Phone” port, all programming, including codes, can be performed.

To change a keyless entry code, the Building Manager picks up the Building Manager's Programming phone, (if both

entry phones are idle, two beeps will be heard to confirm that the C-3000 system is ready for programming) and dials:

(New 4-6 digit entry code) + "#" + (00-96)

For example, to set the Keyless Entry code for apartment 24 to "052069", the Building Manager would enter

"052069#24" and then hang up, unless additional codes need to be changed. Two more beeps from the Building

Manager's programming phone confirm a valid entry, three beeps will signify an error. See the "Programming" section

for full details on the procedure for changing keyless entry codes. Note: Both entry phones are disabled during pro-

gramming.

E. Postal Lock Feature (Authorized Persons Only)

This feature is provided to allow an authorized person, such as a Postal Service worker to gain access to the building

using a special key lock switch dedicated to this purpose. Keying the Postal Lock (momentary contact closure) will acti-

vate door strike 1 contacts for about 5 seconds.

1 2 3 4 5 6 7 8

Komentáře k této Příručce

Žádné komentáře

Viking W-3000 Specifikace Strana 7

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Viking W-3000